FPA‑1000 Analog Addressable Fire Panels

FPA‑1000 Analog Addressable Fire Panels
  • Support for up to 508 points on two analog addressable loops
  • Built-in Ethernet connector for web-browser based programming and Conettix Alarm-over-IP communication
  • Two on-board NACs and dual-line PSTN DACT
  • Peer-to-peer networking of up to eight -V2 panels in a single group
  • Suited to a wide range of applications and compatible with the latest Bosch solutions - including 440 Series Multi-criteria detectors
  • Simple system management and free online training
  • Variety of communication channels
  • Gas detection
 

Product variants

FPA-1000-V2 Пожароизвест. централа, 2 SLC и мрежа

Advanced analog control panel listed by UL for central station, local, auxiliary, and remote station systems with networking capabilities allowing monitoring of up to 2,000 addressable points in one system.

Commercial Type No.: FPA-1000-V2
Product No.: F.01U.213.945

 
FPA-1000-LC Пожароиз. цент., 2 SLC и мрежа, без кор.

FPA‑1000‑UL Mainboard for use as a replacement board for system update or repair

Commercial Type No.: FPA-1000-LC
Product No.: F.01U.214.787

 
 
FPA-1000-LT Аналог./мреж. центр., без трансформатор

FPA‑1000‑V2 fire panel without transformer. For Latin America only.

Commercial Type No.: FPA-1000-LT
Product No.: F.01U.082.721

 

Accessories

BATB-80 Battery box/enclosure, 14x20.75x7.25

BATB-80 Battery box/enclosure, 14x20.75x7.25"

14 x 20.75 x 7.25" (36 x 53 x 18.5 cm). Battery box/enclosure with shelf holds up to four dry or wet cell batteries. Suitable for residential/commercial fire or burglary applications.

Commercial Type No.: BATB-80
Product No.: 4.998.137.931

 
D5070 Analog point programmer, hand-held

D5070 Analog point programmer, hand-held

Used to program address settings on EEPROM‑programmable analog devices

Commercial Type No.: D5070
Product No.: 4.998.800.577

 
 
FAA-325-B4 Analog sensor base, 4

FAA-325-B4 Analog sensor base, 4"

Is combined with analog addressable detectors that use the advanced digital communication protocol to provide early fire warning for life safety and property protection

Commercial Type No.: FAA-325-B4
Product No.: F.01U.133.061

 
FAA-325-B6S Analog sensor base with sounder, 6

FAA-325-B6S Analog sensor base with sounder, 6"

Contains an addressable sounder which provides an audible alarm in the immediate vicinity and only works in combination with one of the FAH‑325, FAI-325, or FAP‑325 analog sensors

Commercial Type No.: FAA-325-B6S
Product No.: F.01U.133.063

 
 
FAA-440-B4 Analog standard base, 4

FAA-440-B4 Analog standard base, 4"

Standard 4-inch base. Used in combination with FAP-440 and FAH-440 detectors to provide early fire warning for life safety and property protection.

Commercial Type No.: FAA-440-B4
Product No.: F.01U.163.849

 
FAA-440-B4-ISO Analog isolator base, 4

FAA-440-B4-ISO Analog isolator base, 4"

4-inch base with built-in isolator. Used in combination with FAP-440 and FAH-440 detectors to provide early fire warning for life safety and property protection.

Commercial Type No.: FAA-440-B4-ISO
Product No.: F.01U.164.309

 
 
FAA-440-B6 Analog standard base, 6

FAA-440-B6 Analog standard base, 6"

Standard 6-inch base. Used in combination with FAP-440 and FAH-440 detectors to provide early fire warning for life safety and property protection.

Commercial Type No.: FAA-440-B6
Product No.: F.01U.164.308

 
FAA-440-B6-ISO Analog isolator base, 6

FAA-440-B6-ISO Analog isolator base, 6"

6-inch base with built-in isolator. Used in combination with FAP-440 and FAH-440 detectors to provide early fire warning for life safety and property protection.

Commercial Type No.: FAA-440-B6-ISO
Product No.: F.01U.164.307

 
 
FAD-325-V2F Kit, analog duct housing w/ smoke head

FAD-325-V2F Kit, analog duct housing w/ smoke head

Duct detector housing with an FAD-325-V2F-DH Analog duct smoke head. It’s easy to install with a drill template. The steel sampling tube means there are no screens or filters to clean.

Commercial Type No.: FAD-325-V2F
Product No.: F.01U.335.528

 
FAH-440 Analog heat detector head, fixed/ROR

FAH-440 Analog heat detector head, fixed/ROR

Use with FAA‑440 family bases and FAP-1000 Analog Addressable Fire Panels to provide general property protection

Commercial Type No.: FAH-440
Product No.: F.01U.163.842

 
 
FAP-325-V2F FAP-325-V2F Analog Photo Detector Flat

FAP-325-V2F FAP-325-V2F Analog Photo Detector Flat

Used to detect fast‑flaming fires and dense smoke typically given off by plastic, foam, paper, wood, and other materials that tend to smolder

Commercial Type No.: FAP-325-V2F
Product No.: F.01U.168.096

 
FAP-440 Analog photoelectric detector head, 24V

FAP-440 Analog photoelectric detector head, 24V

Analog photoelectric smoke detector used with FAA‑440 bases and FAP-1000 fire panels

Commercial Type No.: FAP-440
Product No.: F.01U.163.843

 
 
FAP-440-T Analog photoelectric detector head, 24V

FAP-440-T Analog photoelectric detector head, 24V

Analog photo/heat detector used with FAA‑440 bases and FAP-1000 fire panels

Commercial Type No.: FAP-440-T
Product No.: F.01U.163.844

 
FAP-440-TC Analog detector head, photo/heat/CO

FAP-440-TC Analog detector head, photo/heat/CO

Analog photo/heat/CO detector used with FAA‑440 bases and FAP-1000 fire panels

Commercial Type No.: FAP-440-TC
Product No.: F.01U.163.846

 
 
FAP-440-D Analog dual-photoelectric detector head

FAP-440-D Analog dual-photoelectric detector head

Analog dual-photoelectric smoke detector used with FAA‑440 bases and FAP-1000 fire panels

Commercial Type No.: FAP-440-D
Product No.: F.01U.163.820

 
FAP-440-DT Analog detector head, dual, photo/heat

FAP-440-DT Analog detector head, dual, photo/heat

Analog dual-photoelectric smoke/heat multi-sensor detector used with FAA‑440 bases and FAP-1000 fire panels

Commercial Type No.: FAP-440-DT
Product No.: F.01U.163.845

 
 
FAP-440-DTC Analog detector head, dual, heat/CO

FAP-440-DTC Analog detector head, dual, heat/CO

Analog dual-photoelectric smoke/heat multi-criteria detector used with FAA‑440 bases and FAP-1000 fire panels

Commercial Type No.: FAP-440-DTC
Product No.: F.01U.163.847

 
FCC-380 CO detector (Macurco CM-E1)

FCC-380 CO detector (Macurco CM-E1)

Carbon monoxide detector

Commercial Type No.: FCC-380
Product No.: F.01U.172.606

 
 
FLM-325-2I4 Dual input module for FPA-1000

FLM-325-2I4 Dual input module for FPA-1000

Provides two independent contact monitoring circuits to monitor Normally Open (NO) or Normally Closed (NC) dry contact types of fire alarm devices

Commercial Type No.: FLM-325-2I4
Product No.: F.01U.133.068

 
FLM-325-2R4-2A Dual relay module, 2A

FLM-325-2R4-2A Dual relay module, 2A

Provides 2 A current at two independently-controlled Form C contacts for a variety of Normally Open and Normally Closed applications, compatible with 254 addresses

Commercial Type No.: FLM-325-2R4-2A
Product No.: F.01U.168.098

 
 
FLM-325-2R4-2AI Dual relay module with isolator, 2A

FLM-325-2R4-2AI Dual relay module with isolator, 2A

Provides 2 A current with built-in short circuit isolator circuitry at two independently-controlled Form C contacts for a variety of Normally Open and Normally Closed applications, compatible with 254 addresses

Commercial Type No.: FLM-325-2R4-2AI
Product No.: F.01U.168.099

 
FLM-325-2R4-8A Dual relay module, 8A

FLM-325-2R4-8A Dual relay module, 8A

Provides 8 A current at two independently-controlled Form C contacts for a variety of Normally Open and Normally Closed applications, compatible with 254 addresses

Commercial Type No.: FLM-325-2R4-8A
Product No.: F.01U.168.100

 
 
FLM-325-2R4-8AI Dual relay module with isolator, 8A

FLM-325-2R4-8AI Dual relay module with isolator, 8A

Provides 8 A current with built-in short circuit isolator circuitry at two independently-controlled Form C contacts for a variety of Normally Open and Normally Closed applications, compatible with 254 addresses

Commercial Type No.: FLM-325-2R4-8AI
Product No.: F.01U.168.101

 
FLM-325-CZM4 Conventional zone module for FPA-1000

FLM-325-CZM4 Conventional zone module for FPA-1000

Enables the FACP to interface and monitor up to 25 conventional devices depending on the device type such as two‑wire smoke detectors or pull stations

Commercial Type No.: FLM-325-CZM4
Product No.: F.01U.133.067

 
 
FLM-325-I4-A Contact monitor, class A, 4

FLM-325-I4-A Contact monitor, class A, 4"

Can be wired for Class A or Class B circuits, mounted to a cover plate for a 4‑inch square or double gang electrical back box, bi‑colored LED provides module status, compatible with 254 addresses

Commercial Type No.: FLM-325-I4-A
Product No.: F.01U.168.102

 
FLM-325-I4-AI Contact monitor with isolator class A 4

FLM-325-I4-AI Contact monitor with isolator class A 4"

Can be wired for Class A or Class B circuits, has built‑in short circuit isolator circuitry, mounted to a cover plate for a 4‑inch square or double gang electrical back box, bi‑colored LED provides module status, compatible with 254 addresses

Commercial Type No.: FLM-325-I4-AI
Product No.: F.01U.168.103

 
 
FLM-325-IM Contact monitor for mounting in backbox

FLM-325-IM Contact monitor for mounting in backbox

Allows compatible fire alarm control panels (FACP) to supervise Form A or B dry contact devices in a polling circuit

Commercial Type No.: FLM-325-IM
Product No.: F.01U.216.136

 
FLM-325-ISO Short circuit isolator for FPA-1000

FLM-325-ISO Short circuit isolator for FPA-1000

Isolates a shorted section on a specific polling circuit from the rest of the system to minimize the loss of communication

Commercial Type No.: FLM-325-ISO
Product No.: F.01U.133.071

 
 
FLM-325-NA4 Supervised output module, Class A/B

FLM-325-NA4 Supervised output module, Class A/B

Can be wired for Class A or Class B circuits, compatible with 254 addresses

Commercial Type No.: FLM-325-NA4
Product No.: F.01U.168.104

 
FLM-325-NAI4 Supervised output module, isolator, A/B

FLM-325-NAI4 Supervised output module, isolator, A/B

Built-in short circuit isolator circuitry, can be wired for Class A or Class B circuits, compatible with 254 addresses

Commercial Type No.: FLM-325-NAI4
Product No.: F.01U.168.105

 
 
FMM-325A Analog manual station, single, red

FMM-325A Analog manual station, single, red

The single‑action manual station is UL listed for commercial fire applications and meets Americans with Disabilities Act (ADA) requirements. Set the address on the polling circuit by programming an EEPROM microchip with the D5070 Analog point programmer.

Commercial Type No.: FMM-325A
Product No.: F.01U.246.085

 
FMM-325A-D Analog manual station, double, red

FMM-325A-D Analog manual station, double, red

The double‑action manual station is UL listed for commercial fire applications and meets Americans with Disabilities Act (ADA) requirements. Set the address on the polling circuit by programming an EEPROM microchip with the D5070 Analog point programmer.

Commercial Type No.: FMM-325A-D
Product No.: F.01U.246.087

 
 
FPE-1000-NE Network card, 3-Ethernet

FPE-1000-NE Network card, 3-Ethernet

Ethernet Networking Card for peer‑to‑peer communication in an FPA‑1000‑V2 networked system

Commercial Type No.: FPE-1000-NE
Product No.: F.01U.213.933

 
FMR-1000-RA LCD annunciator FPA-1000 without control

FMR-1000-RA LCD annunciator FPA-1000 without control

LCD annunciator without system control capability for use with the FPA‑1000 Analog Addressable Fire Panels

Commercial Type No.: FMR-1000-RA
Product No.: F.01U.066.880

 
 
FMR-1000-RCMD LCD annunciator FPA-1000 with control

FMR-1000-RCMD LCD annunciator FPA-1000 with control

LCD annunciator with system control capability for use with FPA‑1000 Analog Addressable fire Panels

Commercial Type No.: FMR-1000-RCMD
Product No.: F.01U.066.879

 
FPE-1000-NF Network card, 1-Ethernet 2-fiber optic

FPE-1000-NF Network card, 1-Ethernet 2-fiber optic

Fiber Optic Networking Card for peer‑to‑peer communication in an FPA‑1000 networked system

Commercial Type No.: FPE-1000-NF
Product No.: F.01U.213.943

 
 
FPE-1000-NW Network card, 1-Ethernet 2-wired

FPE-1000-NW Network card, 1-Ethernet 2-wired

Wired Networking Card for peer‑to‑peer communication in an FPA‑1000 networked system

Commercial Type No.: FPE-1000-NW
Product No.: F.01U.213.944

 
FPE-1000-SLC Plug-in SLC module for FPA-1000

FPE-1000-SLC Plug-in SLC module for FPA-1000

Provides a Signaling Line Circuit (SLC) for connection of analog devices to the FPA‑1000 Analog Addressable Fire Panels

Commercial Type No.: FPE-1000-SLC
Product No.: F.01U.073.062

 
 
FPM-1000-ENC Enclosure with dead-front door

FPM-1000-ENC Enclosure with dead-front door

Enclosure with dead front door

Commercial Type No.: FPM-1000-ENC
Product No.: F.01U.214.786

 
FPP-RNAC-8A-4C Power supply, RNAC 8A 24V

FPP-RNAC-8A-4C Power supply, RNAC 8A 24V

When connected to a panel’s option bus, the FPP-RNAC-8A-4C adds four additional NFPA 72, Class B or Class A NACs. When connected directly to the NAC output, it is also a NAC power supply for fire-protective signaling systems.

Commercial Type No.: FPP-RNAC-8A-4C
Product No.: F.01U.003.444